Used- Ingersoll Rand Reciprocating Air Compressor, Model 2475D5. Rated 17.1 cfm at 90 psi. Driven by a 5hp, 3/60/200 volt, 1740 rpm motor. Mounted on an approximate 80 gallon horizontal tank. Serial# 0910210233.

Used- Ingersoll Rand Refrigerated Air Dryer, Model D42IN. Rated 25 cfm. Serial# 09M-012244.

Used-Carrier AquaSnap Air Cooled Chiller, Model 30RBA21062-OD-3. Nominal capacity 210 tons, R-410A refrigerant, 460 volt, 3 phase, 60 hertz. Includes a Comfort Link panel. Serial# 2309Q72966.

Used- York Shipley Donlee Technologies 700HP Boiler, Model SPH-700-N/2. Maximum working pressure steam 300, heating surface 3500, maximum steam capacity 27,600 pounds an hour. National Board# 27714, serial# 97-20277. Includes a North American low nox fuel directed burner, series 4384-18:5118760, serial# 2185548, built 2011, Maxon valves, (1) Cleaver Brooks blowdown separator, (1) Robinson blower type RB1216, serial# 1203420A, driven by a 50hp, 3/60/460 volt, 1770 rpm motor, BFS Industries deaerator tank with (2) pumps and a control panel with Allen-Bradley PowerFlex drives, Allen-Bradley Logix5561 controllers, and an Allen-Bradley PanelView Plus 1000.

Used- Alfa Laval Plate Heat Exchanger, 720.88 Square Feet, Model M15-MFG. Approximate (110) 0.5mm stainless steel plates. Rated 150 psi at -20 to 230 degrees F. Mounted on an expandable carbon steel frame. Serial# 30110-69743, National Board# 26100, built 2007.

Used- Trane CVHF CenTraVac Water Cooled Chiller, Model CVHF640, Approximate 640 Tons. R-123 Refrigerant, 3/60/460 volts. Includes an Adaptive Control panel. Serial# L00H04114.

Used- Marley NC Class Cooling Tower, Approximate 849 Nominal Tons, Model NC8311G2CG. Galvanized housing, stainless steel bottom pan. Serial# NC-820137-A2, built 2007.

Used- Marley NC Class Cooling Tower, Approximate 849 Nominal Tons, Model NC8311G2CG. Galvanized housing, stainless steel bottom pan. Serial# NC-820137-A1, built 2007.

Used- Durco Flowserve MK3 STD Centrifugal Pump, Stainless Steel. Size 3K10X8-16HD-OP/15.88. Driven by a 350hp, 3/60/460 volt, 1785 rpm motor. Serial# 0607-3527, built 2007.

Used- Durco Flowserve MK3 STD Centrifugal Pump, Stainless Steel. 8" inlet and 6" outlet. Driven by a 50hp, 3/60/230/460 volt, 1190 rpm motor. Serial# 4037282, built 2010.

Used- Durco Flowserve Centrifugal Pump, Stainless Steel. Rated 1260 gallons per minute at 157' head. 8" inlet and 6" outlet. Driven by a 150hp, 3/60/230/460 volt, 1790 rpm motor. Serial# 1011MP005436-1.

Used- Durco Flowserve Centrifugal Pump, Stainless Steel. 6" inlet and 4" outlet. Driven by a 75hp, 3/60/460 volt, 3565 rpm motor. Serial# 81049, built 2011.

Used- Durco Flowserve MK3 STD Centrifugal Pump, Stainless Steel. Size 2K3X1.5-10-OP/8.31. Driven by a 40 HP, 3/60/460 volt, 3540 rpm motor. Serial# 0607-3501, built 2007.

Used- Doyle & Roth Shell & Tube Heat Exchanger, Approximate 169 Square Feet, Horizontal. Carbon steel shell rated 150 psi at -20 to 400 degrees F, (81) 1" diameter x 8' long 2205 duplex stainless steel tubes rated 175 psi at -20 to 300 degrees F. 2205 Duplex stainless steel tube sheet, 316L stainless steel heads. Serial# S2196, National Board# 20990, built 2010.

Used- Lancer 815 LX Undercounter Glassware Washer, Serial# 7A063094, Built 2007.

Used- True Manufacturing Refrigerator, Model GDM-49, Serial# 5306957.

Used- Hanson Laboratory Fume Hood, Model 5SA-70. With front glass door. Serial# 3229.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 429464, built 2007. Includes a control panel with an Allen-Bradley Power Flex drive. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 429463, built 2007. Includes a control panel with an Allen-Bradley Power Flex drive. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 435787, built 2007. Includes a control panel with an Allen-Bradley Power Flex drive. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 435786, built 2007. Includes a Yula stainless steel heat exchanger, control panel with an Allen-Bradley Power Flex drive. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 430934, built 2007. Includes a control panel. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 430933, built 2007. Includes a control panel. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 430932, built 2007. Includes a control panel. Mounted on a stainless steel frame with miscellaneous piping and valves.

Used- Waukesha Positive Displacement Pump, Model 130/U2, Stainless Steel. Approximate displacement 0.254 gallons per revolution, nominal capacity to 150 gallons per minute. Driven by a 5hp, 3/60/208-230/460 volt, 1750 rpm gear motor. Serial# 430931, built 2007. Includes a control panel. Mounted on a stainless steel frame with miscellaneous piping and valves.

Unused- Flowserve MK3 STD Centrifugal Pump, Stainless Steel. Size 2K2X1.5US-10A0P-5.94. Driven by a 10hp, 3/60/208-230/460 volt, 3515 rpm motor. Serial# 1088665CHP002A, built 2012.

Used- Thibs Machine & Welding Tank, 400 Gallon, Stainless Steel, Vertical. Approximate 48" diameter x 42" straight side, flat top, coned bottom. Internal rated to 250 degrees F. Top entering Lightnin agitator, model EV6Q50, serial# 4080. Approximate 1" diameter shaft with turbine, driven by a 1/2hp, 3/60/230/460 volt, 1725 rpm motor. Mounted on 4 carbon steel legs. Built 2007.

Used- Clarke Fire Protection Products Diesel Driven Fire Pump System. Consisting of: (1) Clarke diesel engine, model JU4H-UF54, part# WAB, serial# PE4045T769488, built 2009. (1) ITT Industries centrifugal AC fire pump, type 8100, size H6X4X11F, rated 1000 gallons per minute at 347' head at 3000 rpm, serial# 07-049180-01-01/QKD723, (1) control panel with a Firetrol FTA1100-JL12N controller, (1) approximate 60 gallon fuel tank, (1) jockey pump with panel., (1) ITT skid with housing approximate 12' wide x 18' long x 10' tall

Used - Silvan Industries Air Receiving Tank, Approximate 2200 Gallon, Carbon Steel, Vertical. Internal rated 150 psi at -20 to 400 degrees F. Serial# and National Board# 548259, built 2007.

Used- Silvan Industries Air Receiving Tank, Approximate 1040 Gallon, Carbon Steel, Vertical. Internal rated 150 psi at -20 to 450 degrees F. Serial# and National Board# 548702, built 2007.

Unused- Shanghai Heat Transfer Equipment Wide Gap Welded Plate Heat Exchanger, 150 Square Feet, Type LHKD1.0/110-14-W, Stainless Steel. Flow rate tube side 271 cubic feet per hour rated 145 psi at 230 degrees F. , flow rate plate side 78 cubic feet per hour rated 145 psi at 230 degrees F. Serial# 140108, built 2015.

Used 153 Sq. Ft SS Shell and Tube Heat Exchanger. Shell rated 100 PSIG @500F. Tubes rated 80 PSIG @325F. Last use Mol Sieve Condenser.

Used- Belt Conveyor, Stainless Steel. Approximate 24" wide x 144" long stainless steel belt, driven by a 1hp, 3/60/208-230/460 volt, 1140 rpm gear motor. Includes (3) Internal sweepers, (2) driven by a 3/4hp gear motor, (1) missing drive. Mounted carbon steel legs.

Used- Griffin & Company Belt Conveyor, Stainless Steel. Approximate 23" wide x 192" long rubber belt, driven by a 3/4hp, 3/60/230/460 volt, 1700 rpm gear motor. Mounted carbon steel legs. Serial# C-9095-1, built 1983.

Used- Inclined Dewatering Screw Conveyor, Carbon Steel. Approximate 11" diameter x 144" long x 4" pitch screw, driven by a 1.5hp, 3/60/208-230/460 volt, 1755 rpm motor thru a reducer ratio 24.74 to 1. Approximate 3/8" diameter bottom screen holes with discharge chutes.

Used- TPI Industrial Inclined Belt Conveyor, Carbon Steel. Approximate 16" wide x 96" long horizontal bottom section x 288" long inclined section rubber belt with bolt on stainless steel finger pleats space 4" apart, driven by a 3/4hp, 3/60/230/460 volt, 1775 rpm gear motor, ratio 39 to 1. Includes (1) Internal sweeper driven by a 3/4hp gear motor.

Used- Belt Conveyor, Stainless Steel. Approximate 14" wide x 120" long cloth belt, driven by a 3/4hp, 3/60/230/460 volt, 1725 rpm gear motor.

Used- Mueller Plate Heat Exchanger, 32.2 Square Feet, ModelAT10 C-20. (28) Approximate 9" wide x 30" long 316 stainless steel plate. Rated 150 psi at 32 to 300 degrees F. 2" Inlets & outlets, expandable carbon steel frame. Serial# 376094, National Board# 44438, built 2007.

Used- Waukesha Positive Displacement Pump, Model 015, Stainless Steel. Approximate displacement 0.142 gallons per revolution, nominal capacity to 9 gallons per minute. Driven by a 2hp, 3/60/230/460 volt, 1720 rpm gear motor, ratio 3.41 to 1. Serial# 245293, built 1999. Scrapped by Aaron - December 2019

Used- Closed Tube Screw Conveyor, Stainless Steel. Approximate 6" diameter x 480" long screw, driven by a 2hp, 3/60/208-230/460 volt, 1735 rpm motor thru a reducer, ratio 34.94 to 1. Includes a bottom feed hopper.

Used- Thibs Machine & Welding Tank, 438 Gallon, Stainless Steel, Vertical. Approximate 42" diameter x 69" straight side, flat bolt on top, coned bottom. Internal rated to 200 degrees F. Top entering UET agitator, model XCEL-2, serial# 10510-01, built 2007. Approximate 1-1/2" diameter shaft with turbines, driven by a 2hp, 3/60/208-230/460 volt, 1140 rpm motor. Mounted on 4 carbon steel legs. Built 2007.

Used- Thibs Machine & Welding Tank, 438 Gallon, Stainless Steel, Vertical. Approximate 42" diameter x 69" straight side, flat bolt on top, coned bottom. Internal rated to 200 degrees F. Top entering UET agitator, model XCEL-2, serial# 10510-02, built 2007. Approximate 1-1/2" diameter shaft with turbines, driven by a 2hp, 3/60/208-230/460 volt, 1140 rpm motor. Mounted on 4 carbon steel legs. Built 2007.

Used- Thibs Machine & Welding 3 Compartment Tank, 822 Total Gallon, Stainless Steel. Each compartment 274 gallon, approximate 42” x 43” x 46” straight side, flat top, coned bottom, rated to 200 degrees F. Mounted on 8 carbon steel legs, built 2007. Includes (3) Liquiflo stainless steel centrifugal pumps, model 622FS210, serial# 39880-1-1, 39880-1-2, 39880-1-4. Each driven by a 1.5hp, 3/60/208-230/460 volt, 3500 rpm motors.

Used- Thibs Machine & Welding Tank, 202 Gallon, Stainless Steel, Vertical. Approximate 36” diameter x 48” straight side, dished top & bottom. Internal rated 1 psi at 250 degrees F. Side man way, center bottom outlet. Mounted on 4 carbon steel legs. Built 2007.

Used- PCM Progressive Cavity Pump, Type R 20-16, Rated up to 40 gallons per minute at 110 psi. Driven by a 7.5hp, 3/60/230/460 volt, 1765 rpm gear motor, ratio 6.86 to 1. Serial# 262812, built 2007.

Used- Waukesha Positive Displacement Pump, Model 060UL, Stainless Steel. Approximate displacement 0.153 gallons per revolution, nominal capacity to 90 gallons per minute. Driven by a 15hp, 3/60/230/460 volt, 1760 rpm gear motor, ratio 3.89 to 1. Serial# 229417, built 1998.

Used- Moyno Progressive Cavity Pump, Model CFB2FSSB3SAA. Driven by a 7.5hp, 3/60/230/460 volt, 1770 rpm gear motor, ratio 4.82 to 1. Serial# AS2324507.

Used- New Brunswick Innova 4000 Benchtop Incubator Shaker. Serial# 890715388.

Used- Labconco Purifier Class II Biosafety Cabinet, Catalog# 3620904. Approximate 42" wide with front glass door. Serial# 061163128.

Used- Revco Scientific Chest Freezer, Model ULT2075-3-A12, Serial# Y07G-358195-YG.